Home > Could Not > Could Not Set File Security For File Error 1392

Could Not Set File Security For File Error 1392

This may be due to version inconsistencies or due to the absence of the resource DLL on this node. 5080 The specified resource name is supported by this resource DLL. If you disabled simple file sharing in step 3, proceed to the section, "To enable simple file sharing."If you enabled the option for showing hidden files and folders in step 2, proceed It may already have been terminated. 1313 A specified privilege does not exist. 1314 A required privilege is not held by the client. 1315 The name provided is not a properly The value provided for the new password does not meet the length, complexity, or history requirement of the domain. 1326 Logon failure: unknown user name or bad password. 1327 Logon failure: have a peek at this web-site

maribago08-01-2002, 10:03 AMWe were able to solve our problem by forcing the "Uninstall behavior" to be "Install Only (+)". Perform the steps below on the folder reference in your error message. Powered by vBulletin Version 4.2.2 Copyright © 2016 vBulletin Solutions, Inc. Click OK to close ProgramData Properties dialog box. news

Click Edit (2).
Verify that the value of the Permissions column for SYSTEM and Administrators say Full Control. Ask now Contact Us Real help from real people. In addition, this error may be a Windows Installer Issue.

In the Advanced Settings, select Use Simple File Sharing. In the Advanced Settings, deselect Use Simple File Sharing. Joshua02-20-2002, 02:08 PMIs your setup doing anything special to the file or folder specified in the error message? Could not set file security for file C:\Config.msi\.

I was encouraged by a Microsoft engineer to use USERDUMP - in fact this gentleman encouraged me to imbed it in my product as a strategy for diagnosing difficult 'soft realtime' Hope this will help you. Click Edit (2).
Select the Administrators group (1) under Change Owner To, select Replace Owner On Subcontainers And Objects (2), and click OK (3). https://www.kb.blackbaud.co.uk/articles/Article/75197 Verify that the specified log file location exists and that you can write to it. 1623 The language of this installation package is not supported by your system. 1624 Error applying

For information about network troubleshooting, see Windows Help. 1257 The security identifier provided is not from an account domain. 1258 The security identifier provided does not have a domain component. 1259 In Advanced Settings, select Do not show Hidden Files And Folders. Verify that the specified transform paths are valid. 1625 This installation is forbidden by system policy. Please contact your system administrator.

Verify that you have access to that directory. On Windows Vista/7 Click Start and click inside the search dialog. Click OK to close the Folder Options window. Please contact your system administrator. 1270 The smartcard certificate used for authentication has expired.

For any advice many thanks! Check This Out Choose Normal Startup on the General tab, click OK, and restart the computer. Did running the command as a service prevent the command from killing the other process (also a service)? Could not set file security PDA View Full Version : Error 1926.

Include all spaces and quotation marks, and press Enter at the end of each line:

cacls "C:\Config.Msi" /T /E /C /G administrators:F
exit
  Install Adobe Creative Suite 4 or Point Products. Click Permissions, and select Everyone in Group Or User Names. The parent folder to the file being written in the example above is Config.msi and is found directly off Local Disk C. Source For information about network troubleshooting, see Windows Help. 1233 The network location cannot be reached.

If you cannot locate the folder mentioned, enable hidden files and folders. In the Command Prompt window, type the following commands exactly as they appear below. Could not set file security for file.

Make sure everyone is listed with full control.

Try to create a folder called "Config.Msi" on hard disk "C:\" and check the properties of the new created folder. Install Adobe Creative Suite 4 or Point Product. The value provided for the new password contains values that are not allowed in passwords. 1325 Unable to update the password. Install Adobe Creative Suite 4 or Point Product.

Error happens when the install attempts to create the BOINC folder itself. The table below describes system Exit/Error codes when a task is executed. Use your global user account or local user account to access this server. 1808 The account used is a computer account. have a peek here Characters Remaining: 255 Blackbaud Community Connect and collaborate with fellow Blackbaud users.

Verify that you have sufficient privileges to modify the security permissions for this file" :confused: How do I have to adapt the setup in order to avoid this message? Submit feedback to IBM Support 1-800-IBM-7378 (USA) Directory of worldwide contacts Contact Privacy Terms of use Accessibility Project Help Donate Porting Graphics Add-ons Science About [email protected] About Astropulse Science newsletters In the Folder Options window, select the View tab. Please type your message and try again.

The caller now needs to enumerate the files to find the changes. 1051 A stop control has been sent to a service that other running services are dependent on. 1052 The Right-click on Command Prompt and select Run As Administrator. United States Copyright © Apple Inc. Contact your support personnel for assistance. 1602 User cancelled installation. 1603 Fatal error during installation. 1604 Installation suspended, incomplete. 1605 This action is only valid for products that are currently installed.

Feedback Please tell us how we can make this article more useful. i There's a Cross _|_ r h to bridge | c the Great Divide.. | Rich Pennenga -- Voice/Fax (732) 817-5927 Avaya, Rm 2B-530A, 101 Crawfords Corner Road Holmdel, NJ 07733 Dim oShell, MyApp, i Set oShell = CreateObject("WScript.Shell") MyApp = """C:\MyApplication\Setup.exe"" /Q" i = 0 i = oShell.Run(MyApp, 1 ,True) WScript.Echo "Exit Code is: " & (i) Set oShell = Nothing